PDP-11 simulator V3.6-0
sim> set cpu 11/45
Disabling XQ
sim> set rl0 rl01
sim> set rl1 rl01
sim> att rl0 rsxm26.dsk
sim> att rl0 mapsrc.dsk
sim> boo rl0


  RSX-11M V3.2 BL26   28K 
>RED DL:=SY:
>RED DL:=LB:
>MOU DL:RSXM26
>@DL:[1,2]STARTUP
>* PLEASE ENTER TIME AND DATE (HR:MN DD-MMM-YY) [S]: 01:58 10-JUL-99
>TIM 01:58 10-JUL-99
>* ENTER LINE WIDTH OF THIS TERMINAL [D D:132.]: 80.
>SET /BUF=TI:80.
>;
>; NOTE - The Baseline INDirect must be replaced by BIGIND with 
>;      a priority of 10. for SYSGEN.
>;
>;  ie  >REM ...AT.
>;      >INS $BIGIND/PRI=10.
>;
>@ <EOF>
>INS $BOO
>BOO [1,54]

  RSX-11M V3.2 BL26   124K   MAPPED
>RED DL:=SY:
>RED DL:=LB:
>MOU DL:RSXM26
>@DL:[1,2]STARTUP
>* PLEASE ENTER TIME AND DATE (HR:MN DD-MMM-YY) [S]: ^Z

>@ <EOF>
>SAV /WB
DMO -- TT0:   DISMOUNTED FROM DL0:    *** FINAL DISMOUNT ***
 *** DL0:  -- DISMOUNT COMPLETE 

>

  RSX-11M V3.2 BL26   124K   MAPPED
>RED DL:=SY:
>RED DL:=LB:
>MOU DL:RSXM26
>@DL:[1,2]STARTUP
>* PLEASE ENTER TIME AND DATE (HR:MN DD-MMM-YY) [S]: 01:59 10-JUL-99
>TIM 01:59 10-JUL-99
>* ENTER LINE WIDTH OF THIS TERMINAL [D D:132.]: 80.
>SET /BUF=TI:80.
>ACS SY:/BLKS=512.
>;
>; NOTE - The Baseline INDirect must be replaced by BIGIND with 
>;      a priority of 10. for SYSGEN.
>;
>;  ie  >REM ...AT.
>;      >INS $BIGIND/PRI=10.
>;
>@ <EOF>
>REM AT.
>INS $BIGIND/PRI=10.
INS -- WARNING - PRIVILEGED TASK OVERMAPS I/O PAGE
>INS $PIP
>SET /UIC=[1,50]
>PIP *.*;*/DE
>MOU DL1:/OVR
>PIP DL1:[1,54]*.*;*/DE
>DMO DL1:
DMO -- TT0:   DISMOUNTED FROM DL1:    *** FINAL DISMOUNT ***
 *** DL1:  -- DISMOUNT COMPLETE 

>SET /UIC=[200,200]
>@SYSGEN
>;
>; RSX-11M Ver. 3.2 BL26 System Generation 3.2.2d done on 10-JUL-99 at 02:00:02
>;
>; Copyright (C) 1979 Digital Equipment Corporation, Maynard Mass.
>;
>; RL01 distribution kit
>;
>*  1. Inhibit MCR command lines (Type <ESC> for explanation)? [Y/N]:
>*  2. Have you made a copy of the distribution kit? [Y/N]:Y
>*  3. Use saved or canned answer file for input responses? [Y/N]:
>* 10. Save responses (i.e.: create SYSSAVED.DAT)? [Y/N]:Y
>* 11. UIC for SYSSAVED files if not [200,200]  [S]: 
>* 12. UIC for SYSGEN command files if not [200,200] [S]: 
>* 13. Clean up files from previous GENs? [Y/N]:Y
>* 14. Device, when ready, for Executive sources (ddu:)  [S]: DL1:
>;
>MOU DL1:MAPSRC
>ASN DL1:=LB:
>;
>SET /UIC=[1,1]
>PIP [1,20]RSXBLD.CMD;*/DE/NM,SYSPAR;*
>PIP [1,24]RSXBLD.CMD;*/DE/NM,TTDRVBLD;*,SYSPAR;*
>PIP [1,50]SYSVMR.CMD;*/DE/NM,[1,54]SYSVMR;*
>PIP [11,20]*.OBJ;*/DE/NM,*.UDC;*,*.ICR;*,*.IDS;*,*.PCS;*
>PIP [11,20]RSXASM.CMD;*/DE/NM,RSXDRVASM;*,RSXBLD;*
>PIP [11,24]*.OBJ;*/DE/NM,*.UDC;*,*.ICR;*,*.IDS;*,*.TTY;*,*.PCS;*
>PIP [11,24]RSXASM.CMD;*/DE/NM,RSXDRVASM;*,RSXBLD;*
>PIP [11,10]SYSTB.MAC;*/DE/NM,ICTAB;*,RSXMC;*,[200,200]SGNPARM.CMD;*
>PIP [11,10]RSXASM.CMD;*/DE/NM,RSXDRVASM;*,RSXBLD;*
>PIP /FR

DL0: HAS 5584. BLOCKS FREE, 4656. BLOCKS USED OUT OF 10240.
LARGEST CONTIGUOUS SPACE = 3305. BLOCKS

>SET /UIC=[11,10]
>;
>; Target configuration
>;
>*  1. Processor (e.g.: 11/34, LSI-11) [S R:5-6]: 11/45
>*  3. Generating RSX-11S? [Y/N]:
>*  4. Memory size (in K-word blocks) [D R:16.-124.]: 124.
>*  5. Mapped? [Y/N]:Y
>*  6. Any K-series laboratory devices? [Y/N]:
>*  8. Floating point processor (FP-11) present? [Y/N]:Y
>* 10. If using KW11-P as system clock: number of intrps./sec. [D R:0.-1000.]: 
>* 11. Line frequency:   A- 60 Hz    B- 50 Hz   [D: "A"] [S]: B
>* 12. KW11-Y Watchdog timer support? [Y/N]:
>* 13. Memory parity support? [Y/N]:
>* 15. Highest interrupt vector (If 0 will be computed) [O R:0-774]: 774
>;     For device configuration: "*" Prints device table, "." Terminates inquiry
>;     Enter devices and number of controllers for devices which require drivers
>* 16. Devices [S]: *
>;
>;     Physical devices:
>;    
>;     AD- ad01-d a/d contr  AF- afc11 a/d contrlr AR- ar11 lab subsystem
>;     CR- cr11/cm11 crd rdr CT- ta11/tu60 cass    DB- rp04/05/06 disk pack
>;                                                 DD- tu58 cartridge dectape
>;     DF- rf11 fixed disks  DK- rk11/rk03/rk05    DL- rl11/rl01/rl02 disk
>;     DM- rk611/rk06 disks  DP- rp11/rp02/rp03    DR- rm02/rm03 disk drives
>;     DS- rs/rs03/04 fx dsk DT- tc11/tu56 dectape DX- rx11/rx01 floppy disk
>;                           DY- rx02 floppy disk  GR- vt11/vs60 graphics sys
>;     IC- ics/icr11 contrlr IP- ip11/ip300 cntrlr IS- drs/dss11 modules
>;     LA- lpa11 lab subsys  LP- lp/ls/lv/11 prntr LS- lps11 lab subsystems
>;     MM- tu16/45/77/te16   MS- ts04 tape drive   MT- tm11/tu10/te10/ts03 tape
>;     PP- paper tape punch                        PR- pr11 papertape reader
>;     UD- udc11 uni contr   XB- da11-b uni links  XL- dl11-e async lines
>;     XM- dmc11 inproc lnk  XP- dp11 sync inter   XQ- dq11 sync interface
>;     XU- du11 sync inter   XW- dup11 sync interface
>;
>;     Non-physical devices: maximum of one "controller" specifiable
>;    
>;     CO- console driver    NL- the null device   TT- terminal driver
>;    
>;     Enter responses as: dev1=number controllers,dev2=number controllers, ...
>;
>;     Example: DK,DM=2,TT,NL (NOTE: No number of controllers implies one)
>;
>* 16. Devices [S]: NL,LP,TT,CO,DL,DR,MT.
>;
>; Processor:11/45   Memory Size:124K,Mapped   System:RSX-11M
>;
>; Host configuration
>;
>*  1. Are you running SYSGEN standalone (on the baseline system)? [Y/N]:
>*  2. Is a line printer available? [Y/N]:
>*  4. Does the listing/map device have at least 120 columns? [Y/N]:
>*  5. Assembly listings device (ddu:) [D: "NL:"] [S]: 
>*  6. Map device for Executive and device drivers (ddu:) [D: SY:] [S]: DL0:
>;
>* EOS * Do you want to: <CR>-continue R-repeat section E-exit P-pause [S]: 
>;
>; Executive Options
>;
>;     Answer Y(ES) if the following support is desired
>;
>*  1. Will DBMS-11 be used? [Y/N]:Y
>;     Files-11 ACP support will be included
>*  3. RMS record locking and placement control? [Y/N]:Y
>*  4. Non-resident tasks (task loader)? [Y/N]:Y
>*  5. Loadable task loader? [Y/N]:Y
>;     Memory management directives (PLAS) support will be included
>;     Send/Receive by reference support will be included
>*  8. Get mapping context directive? [Y/N]:Y
>;     Address checking support will be included
>;     I/O rundown support will be included
>* 11. Multi-user protection? [Y/N]:Y
>* 12. ANSI Magtape ACP? [Y/N]:Y
>* 13. On-line formatting (FMT) or on-line user-mode diagnostics? [Y/N]:Y
>* 14. Loadable device drivers? [Y/N]:Y
>* 15. Should the default for all applicable drivers be loadable? [Y/N]:Y
>;     AST support will be included
>;     Cancel selective MARKTIMEs support will be included
>* 17. Task termination and device not ready messages (TKTN)? [Y/N]:Y
>* 18. Power fail recovery? [Y/N]:
>* 19. Install, request, and remove on exit? [Y/N]:Y
>* 20. Large (20K) Executive? [Y/N]:Y
>* 21. Logical device assignment? [Y/N]:Y
>* 22. Logging of device errors and timeouts? [Y/N]:Y
>* 23. Logging of undefined interrupts? [Y/N]:Y
>* 25. Do you intend to include a user-written driver? [Y/N]:
>* 28. Disk writecheck? [Y/N]:Y
>* 29. Executive Debugging Tool (XDT)? [Y/N]:Y
>* 30. Rotating pattern in data lights? [Y/N]:
>* 31. Industrial network or DECnet? [Y/N]:
>* 32. Queue manager and queued print spooler? [Y/N]:Y
>* 33. Group global event flags? [Y/N]:Y
>;     For directives: "*" Prints table, "." Terminates inquiry, "%" Gets all
>* 34. Enter code for directives [S]: %
>* 34. Enter code for directives [S]: .
>* 35. Number of pre-allocated QIO packets [D R:0.-15. D:5.]: 
>* 36. Size of data transfer vector in words [D R:5.-33. D:33.]: 
>* 37. Round-robin scheduling interval in ticks [D R:0.-1000. D:5.]: 
>* 38. Highest priority class for consideration [D R:1.-249. D:150.]: 
>* 39. Lowest priority class for consideration [D R:1.-150. D:1.]: 
>* 40. Executive level disk swapping interval [D R:0.-5000. D:30.]: 
>* 41. Swapping priority [D R:1.-20. D:5.]: 
>* 42. Size of dynamic storage region (POOL) in words [D R:256.-16384. D:1024.]:
>* 43. Seconds between printer not ready messages [D R:0.-255. D:30.]: 
>* 45. System crash register and stack dump device CSR [O R:0-177700 D:177564]: 
>* 46. Checkpointing:             A- Yes    B- With system ckpnt. file    [S]: B
>* 47. System cntrled partitions: A- Yes    B- With auto compaction (SHF) [S]: B
>* 48. Dump analysis:             A- PANIC  B- Crash (CDA)                [S]: B
>* 49. Output notification device CSR [O R:160000-177700 D:177564]: 
>* 50. Memory dump device (ddu:) [S R:3-4]: MT0:
>* 51. CSR address of dump device [O R:160000-177700 D:172522]: 
>;
>; Terminal driver options
>;
>*  1. Terminal driver desired (A/B/C/D, * prints table) [S]: *
>;
>;     Terminal drivers:  A- Tailorable half duplex
>;                        B- Tailored half duplex (user-oriented)
>;                        C- Full duplex
>;                        D- Baseline half duplex
>;
>*  1. Terminal driver desired (A/B/C/D, * prints table) [S]: C
>*  2. Unsolicited input timeout value in seconds [D R:0.-2540. D:120.]: 
>;
>;     Answer Y(ES) if the following support is desired
>;
>*  5. Task checkpointable during terminal input? [Y/N]:Y
>*  6. Unsolicited input character AST? [Y/N]:Y
>;     Breakthrough write support will be included
>;     CTRL/R support will be included
>* 10. Escape sequence handling? [Y/N]:Y
>* 11. Get multiple characteristics? [Y/N]:Y
>* 12. Set multiple characteristics? [Y/N]:Y
>* 13. Get terminal driver options? [Y/N]:Y
>* 17. Read after prompt? [Y/N]:Y
>* 20. CRT rubout support? [Y/N]:Y
>* 25. Hardware unrecoverable input error notification? [Y/N]:Y
>* 26. Device independent cursor positioning? [Y/N]:Y
>;
>* EOS * Do you want to: <CR>-continue R-repeat section E-exit P-pause [S]: 
>;
>;     Thinking ...
>;
>; End of Executive option generation at 02:02:51 on 10-JUL-99
>;
>; Peripheral configuration
>;
>;     Parameters  appearing  in  square  brackets  "[...]"  can  only be
>;     specified  for  the  first  controller  of  a  particular  device.
>;     Parameters appearing in parentheses "(...)" only need be specified
>;     if   the  indicated  option  is  present  on  the  target  system.
>;    
>;     The   default  for  loadable  drivers  has  been  set  to  *TRUE*.
>;     To override this setting enter R (resident) as the first parameter
>;     for    the    first    controller   of   the   specified   device.
>;    
>; A/D and Laboratory devices: None specified
>;
>; Interprocessor communication devices: None specified
>;
>; Unit record devices: LP
>;
>; Enter [L/R,] vector, CSR, printer type
>;              (,[KMC timeout count <0=no KMC>, KMC vector, KMC CSR]) for:
>;
>* 16. LP controller 0 [D: 200,177514,LA180,0,300,160130] [S]: 
>;
>; Disks: DL, DR
>;
>; Enter [L/R,] vector, CSR, number of drives for:
>;
>*  3. DL controller 0 [D: 160,174400]              [S]: ,,4
>* 53. Contr 0 unit 0. is an RL01/RL02 [D: RL01]    [S]: RL02
>* 53. Contr 0 unit 1. is an RL01/RL02 [D: RL01]    [S]: RL02
>* 53. Contr 0 unit 2. is an RL01/RL02 [D: RL01]    [S]: RL02
>* 53. Contr 0 unit 3. is an RL01/RL02 [D: RL01]    [S]: RL02
>;
>; Enter [L/R,] vector, CSR, number of drives, unit number of first drive,
>;              [O=offset recovery support/NO=no support] for:
>;
>*  2. DR controller 0 [D: 254,176700,,0,O]         [S]: ,,8
>* 56. Contr 0 unit 0. is an RM02/RM03 [D: RM03]    [S]: 
>* 56. Contr 0 unit 1. is an RM02/RM03 [D: RM03]    [S]: 
>* 56. Contr 0 unit 2. is an RM02/RM03 [D: RM03]    [S]: 
>* 56. Contr 0 unit 3. is an RM02/RM03 [D: RM03]    [S]: 
>* 56. Contr 0 unit 4. is an RM02/RM03 [D: RM03]    [S]: 
>* 56. Contr 0 unit 5. is an RM02/RM03 [D: RM03]    [S]: 
>* 56. Contr 0 unit 6. is an RM02/RM03 [D: RM03]    [S]: 
>* 56. Contr 0 unit 7. is an RM02/RM03 [D: RM03]    [S]: 
>;
>; Tapes: MT
>;
>; Enter [L/R,] vector, CSR, number of drives for:
>;
>*  3. MT controller 0 [D: 224,172522]              [S]: ,,4
>;
>; Non-physical (pseudo) devices: CO, TT, NL, TI, CL, LB, SY
>;
>; Enter [L/R,] terminal number to redirect to (TTn:) for:
>;
>* 18. CO controller 0 [D: 0]                       [S]: 
>;
>; Enter num. DL11's <ZL>, num. DH11's, num. DZ11's, num. DJ11's for:
>;
>* 20. The terminal driver  [D: 1,0,0,0]            [S]: ,,4
>;
>; Enter vector, CSR for:
>;
>* 21. ZL controller 0 [D: 60,177560]               [S]: 
>;
>; Enter vector, CSR, highest line number <0 to 7> [, answer speed] for:
>;
>* 24. DZ controller 0 [D: ,,,0]                    [S]: 300,160100,7,9600
>* 24. DZ controller 1                              [S]: 310,160110,7
>* 24. DZ controller 2                              [S]: 320,160120,7
>* 24. DZ controller 3                              [S]: 330,160130,7
>SET /UIC=[1,24] ! Creating TTDRVBLD.CMD
>SET /UIC=[11,10]
>;
>* EOS * Do you want to: <CR>-continue R-repeat section E-exit P-pause [S]: 
>;
>;
>; End of interrupt vector area has been set to 1000
>;
>;
>; Create Executive build files
>;
>PIP RSXMC.MAC=LB:RSXMC0.MAC/AP
>;
>; Assemble the Executive
>;
>PIP [11,24]/NV=RSXASM.CMD,RSXDRVASM.CMD
>PIP RSXASM.CMD;0/DE,RSXDRVASM;0
>;
>*  1. Do you wish to edit any of the Executive files? [Y/N]:
>;
>;
>* EOS * Do you want to: <CR>-continue R-repeat section E-exit P-pause [S]: 
>;
>INS SY:$BIGMAC
INS -- PARTITION PAR14K NOT IN SYSTEM, DEFAULTING TO GEN
>;SET /TEABREAK=TI: Start of Executive assembly at 02:04:25 on 10-JUL-99
>SET /UIC=[11,24]
>MAC @RSXASM
>;SET /NOTEABREAK=TI: Executive assembly ended at 02:04:55 on 10-JUL-99
>;
>* EOX * Did the Executive assemble correctly? [Y/N]:Y
>;
>;SET /TEABREAK=TI: Start of device drivers assembly at 02:04:57 on 10-JUL-99
>SET /UIC=[11,24]
>MAC @RSXDRVASM
>;SET /NOTEABREAK=TI: Device drivers assembly ended at 02:05:27 on 10-JUL-99
>;
>* EOX * Did the device drivers assemble correctly? [Y/N]:Y
>;
>REM MAC
>;
>; Prepare for task building
>;
>PIP RSX.OBS=*.OBJ
>PIP *.OBJ;*/DE/NM
>PIP RSX11M.OBJ/RE=RSX.OBS
>PIP TTDRV.OBJ=*.TTY
>PIP *.TTY;*/DE/NM
>SET /UIC=[1,24]
>PIP /NV=[11,10]RSXBLD.CMD
>;
>* EOS * Do you want to: <CR>-continue R-repeat section P-pause [S]: 
>;
>;
>; End of SYSGEN phase I at 02:05:35 on 10-JUL-99
>;     -- To continue type: @[200,200]SYSGEN2
>;
>SET /UIC=[200,200]
>@ <EOF>
>DMO DL1:
DMO -- TT0:   DISMOUNTED FROM DL1:    *** FINAL DISMOUNT ***
 *** DL1:  -- DISMOUNT COMPLETE 

>ASN =LB:
>INS $LBR
>INS $VMR
>@SYSGEN2
>;
>; RSX-11M Version  3.2 System Generation Phase II started 10-JUL-99 at 02:06:34
>;
>; Copyright (C) 1979 Digital Equipment Corporation, Maynard Mass.
>;
>*  1. In what UIC is SGNPARM.CMD if not [200,200] [S]: 
>;
>; RL01 distribution kit SYSGEN versions 3.2.2d / 2:3.2.2d  for RSX11M BL26
>;
>; Continuation from SYSGEN phase I done on 10-JUL-99 at 02:05:33
>;
>;     The map device ( DL0: ) must already be mounted with UIC [1,34].
>;     If  it  is  not,  ^Z  SYSGEN2  at  the  next  question and do so.
>;
>*  2. Expanded comments desired for SYSGEN phase II? [Y/N]:Y
>*  3. Is SYSGEN still running on-line? [Y/N]:Y
>;
>;     If running a single RL01 kit enter either "NO" or "NONE" in response
>;     to the next question if the [1,24] files have not been copied
>;     onto the RSXM26 disk. 
>;
>;     Note that it will first be necessary to delete [11,10]*.MAC; however
>;     before you do this first copy RSXMC.MAC and SYSTB.MAC to some other
>;     UIC.
>;
>*  5. If not in DL1: enter object files device when ready (ddu:) [S]: 
>;
>MOU DL1:MAPSRC
>ASN DL1:=LB:
>ASN SY:=TK:
>PIP /FR

DL0: HAS 5068. BLOCKS FREE, 5172. BLOCKS USED OUT OF 10240.
LARGEST CONTIGUOUS SPACE = 3204. BLOCKS

>*  6. Have you already built the libraries, the Exec, and the loadable drivers?
>;
>; Start of Executive and driver build phase at 02:06:44 on 10-JUL-99
>;
>;
>; Create system libraries at 02:06:44 on 10-JUL-99
>;
>SET /UIC=[1,1]
>PIP ANSLIB.OLB/NV=SYSLIB.OLB
>LBR ANSLIB/RP=LB:FCSMTA
MODULE "ANSPAD" REPLACED

MODULE "ASSLUN" REPLACED

MODULE "BIGBUF" REPLACED

MODULE "CLOSE " REPLACED

MODULE "CREATE" REPLACED

MODULE "DIRECT" REPLACED

MODULE "GET   " REPLACED

MODULE "GETSQ " REPLACED

MODULE "OPEN  " REPLACED

MODULE "OPFID " REPLACED

MODULE "OPFNB " REPLACED

MODULE "POINT " REPLACED

MODULE "PUT   " REPLACED

MODULE "PUTSQ " REPLACED

MODULE "RDWAIT" REPLACED

MODULE "RETADR" REPLACED

MODULE "RWBLK " REPLACED

MODULE "WATSET" REPLACED

MODULE "WTWAIT" REPLACED

>SET /UIC=[1,24]
>PIP RSX11M.OLB;*/DE/NM,TTDRV;*
>LBR RSX11M/CR:80.:640.:256.=[11,24]RSX11M.OBJ
>LBR TTDRV/CR:52.:256.:64.=[11,24]TTDRV.OBJ
>PIP LB:/NV=LB:MCR.OLB
>LBR LB:MCR/RP=LB:MCRTTFD
MODULE "SDSOV " REPLACED

MODULE "SETOV " REPLACED

MODULE "SPROV " REPLACED

>;
>; Taskbuild the Executive and the terminal driver at 02:06:47 on 10-JUL-99
>;
>PIP [1,34]*.*;*/DE/NM
>TKB @RSXBLD
>;
>* EOX * Did the Executive build successfully? [Y/N]:Y
>;
>SET /UIC=[1,54]
>PIP LB:/NV=RSX11M.STB
>SET /UIC=[1,24]
>TKB @TTDRVBLD
>;
>* EOX * Did the terminal driver build successfully? [Y/N]:Y
>;
>* 10. List Executive map? [Y/N]:
>;
>; Build Loadable drivers
>;
>*  6. Device for driver's maps [D: NL:] [S]: DL0:
>*  9. Build all selected loadable drivers into DRVPAR? [Y/N]:Y
>;
>TKB @[200,200]CODRVBLD
>PIP [200,200]CODRVBLD.CMD;*/DE
>PIP [1,54]CODRV.STB/TR
>TKB @[200,200]DLDRVBLD
>PIP [200,200]DLDRVBLD.CMD;*/DE
>PIP [1,54]DLDRV.STB/TR
>TKB @[200,200]DRDRVBLD
>PIP [200,200]DRDRVBLD.CMD;*/DE
>PIP [1,54]DRDRV.STB/TR
>TKB @[200,200]LPDRVBLD
>PIP [200,200]LPDRVBLD.CMD;*/DE
>PIP [1,54]LPDRV.STB/TR
>TKB @[200,200]MTDRVBLD
>PIP [200,200]MTDRVBLD.CMD;*/DE
>PIP [1,54]MTDRV.STB/TR
>;
>; End of library, Executive and driver build phase at 02:07:05 on 10-JUL-99
>;
>; Start task building privileged tasks at 02:07:05 on 10-JUL-99
>;
>* 11. FCP desired  (Type <ESC> for explanation)  [D: MIDDLE] [S]: 
>;
>;     Five FCP's are supported by SYSGEN.  They are:
>;
>;     Non-multiheader  - Minimum functionality (Size: 2K)
>;     Small            - Full functionality, heavily overlayed (2.25K)
>;     Middle           - Default, optimized for RMS, open/close envir. (5.2K)
>;     Large            - Optimized for all applications (6.7K)
>;     PLAS             - Fastest possible, optimized for create/delete (10.1K)
>;
>* 11. FCP desired  (Type <ESC> for explanation)  [D: MIDDLE] [S]: PLAS
>* 13. Build the unprivileged queue manager utilities? [Y/N]:Y
>* 14. Build the task PMD? [Y/N]:Y
>* 15. Build RMDEMO? [Y/N]:Y
>;
>;     Note that the following task-builds will be executed for your system:
>;
>;       BOOBLD    DMOBLD    COTBLD    FCPPRO2BLD INDBLD    INIBLD    INSBLD    
>;       MCRMUBLD  MOUBLD    QMGBLD    QMGCLIBLD QMGPRTBLD LPPBLD    F11MSGBLD 
>;       MTABLD    SAVBLD    TKNBLD    UFDBLD    LOABLD    UNLBLD    PMDBLD    
>;       RMDBLD    SHFBLD    ACNTBLD   BYEBLD    HELBLD    BROBLD    SHUTUPBLD 
>;       ACSBLD    ERFBLD    ERLBLD    
>;
>* 17. Edit any privileged task build files? [Y/N]:
>; 
>;     For the dual RK05 or RL01 distribution kits, running standalone,
>;     you may direct the task builder maps to the line printer, or to
>;     printer, or another disk of the same type as your kit.  Note that
>;     the maps will not fit on the distribution disks for the above.
>; 
>;     For other distribution kits, you may specify the line printer,
>;     the distribution kit disk (SY0) or a second disk of the same type.
>; 
>;     For all online SYSGENs, you may specify any disk with at least
>;     1400 free blocks.  Note that SYSGEN will not load the driver for
>;     this disk.
>; 
>* 18. Map device for privileged tasks (ddu:) [D: NL:] [S]: DL0:
>;
>ASN DL0:=MP:
>* 18. Is DL0: mounted as a Files-11 volume with UFD [1,34]? [Y/N]:Y
>ASN LB:=SY:
>ASN =LB:
>ASN =SY:
>ASN DL1:=SY:
>ASN DL0:=LB:
>TKB @BOOBLD
>TKB @DMOBLD
>TKB @COTBLD
>TKB @FCPRO2BLD
>TKB @INDBLD    ! GENERATING SMALL INDIRECT
>TKB @INIBLD
>TKB @INSBLD
>TKB @MCRMUBLD
>TKB @MOUBLD
>TKB @QMGBLD
>TKB @QMGCLIBLD
>TKB @QMGPRTBLD
>TKB @LPPBLD
>TKB @F11MSGBLD
>TKB @MTABLD
>TKB @SAVBLD
>TKB @TKNBLD
>TKB @UFDBLD
>TKB @LOABLD
>TKB @UNLBLD
>TKB @PMDBLD
>TKB @RMDBLD
>TKB @SHFBLD
>TKB @ACNTBLD
>TKB @BYEBLD
>TKB @HELBLD
>TKB @BROBLD
>TKB @SHUTUPBLD
>TKB @ACSBLD
>TKB @ERFBLD
>TKB @ERLBLD
>;
>* EOX * Did the privileged tasks build successfully? [Y/N]:Y
>;
>; End of privileged task builds at 02:08:11 on 10-JUL-99
>;
>ASN LB:=SY:
>ASN =LB:
>ASN =SY:
>ASN DL0:=SY:
>ASN DL1:=LB:
>SET /UIC=[1,54]
>PIP /FR

DL0: HAS 1831. BLOCKS FREE, 8409. BLOCKS USED OUT OF 10240.
LARGEST CONTIGUOUS SPACE = 1669. BLOCKS

>;
>;     SGN -- SYSGEN will now pause to allow you to create your
>;            RSX11M.SYS file using the following example.  Ideally
>;            your system it should occupy the same number of blocks
>;            as indicated in the example.
>;
>;            PIP RSX11M.SYS/NV/CO/BL:498.=RSX11M.TSK

AT. -- PAUSING. TO CONTINUE TYPE "RES ...AT."

>PIP RSX11M.SYS/NV/CO/BL:498.=RSX11M.TSK
>RES ...AT.
>

AT. -- CONTINUING
>; 
>;     Your target system is now ready to set up partitions and install
>;     the required tasks.  SYSGEN has created a file SYSVMR.CMD; edit
>;     this command file to do the following:
>;
>;     1) Extend pool space to base of first partition
>;     2) Set up your partitions, particularly your device partitions
>;     3) Install the privileged tasks you just built
>;     4) Load any loadable drivers that you want resident
>;        in the system image.  If the terminal and/or system
>;        disk drivers are loadable, they must be loaded using VMR.
>; 
>;     When VMR prompts ENTER FILENAME> respond with @SYSVMR
>;
>;     Note that for mapped systems the SYSVMR file will typically
>;     produce a valid system image without editing; for unmapped
>;     systems no such claim is made.  It is, however, our best guess.
>;     Note that on unmapped systems no driver partitions are created
>;     by SYSGEN.  You must edit them in yourself.
>;
>;
>* 19. Edit SYSVMR.CMD? [Y/N]:
>;
>ASN SY:=LB:
>VMR
ENTER FILENAME: @SYSVMR
VMR -- INSTALLED TASKS MAY NO LONGER FIT IN PARTITION
SET /TOP=DRVPAR:-*
VMR -- FILE NOT FOUND
INS F11MSG      ! INSTALL MAGTAPE ERROR PROCESSOR
POOL=1200:7046.:07046.
LDRPAR 117734 120000 002400 MAIN TASK
TTPAR  117420 122400 040000 MAIN TASK
DRVPAR 117074 162400 013600 MAIN SYS 
       117030 162400 002000 SUB  DRIVER - DL:
       116730 164400 002300 SUB  DRIVER - DR:
       116630 166700 001100 SUB  DRIVER - LP:
       116530 170000 003200 SUB  DRIVER - MT:
       116430 173200 003000 SUB  DRIVER - CO:
SYSPAR 116364 176200 010000 MAIN TASK
FCPPAR 116320 206200 047300 MAIN SYS 
GEN    116254 255500 502300 MAIN SYS 
...LDR 11     117634 LDRPAR 248. 002400 LB0:-00003033 FIXED
TKTN   03.94  112754 SYSPAR 248. 010000 LB0:-00015651
...RMD V01    115254 GEN    225. 040000 LB0:-00017062
MTAACP 0010   114454 GEN    200. 013500 LB0:-00016256
...DMO 22.00  114754 GEN    160. 040000 LB0:-00003450
MCR... 02.01  113654 SYSPAR 160. 010000 LB0:-00004761
...MOU 22.15  113354 GEN    160. 040000 LB0:-00003500
...MCR 01     113054 GEN    160. 020000 LB0:-00005101
F11ACP M0320  116154 FCPPAR 149. 047300 LB0:-00004007
COT... 00.01  116054 GEN    145. 040000 LB0:-00003620
PMD... 05     114054 GEN    140. 020000 LB0:-00017175
SHF... 04     113154 SYSPAR 105. 010000 LB0:-00016616
...INS 04     114154 GEN    100. 040000 LB0:-00004142
...SAV 04.22  113254 GEN    100. 040000 LB0:-00016203
...UFD V0410  112654 GEN    100. 040000 LB0:-00015734
QMG... 01.04  115754 GEN     75. 040000 LB0:-00015405
PRT... 01.01  115454 GEN     70. 040000 LB0:-00003650
LPP0   01.06  115354 GEN     70. 040000 LB0:-00015751
...AT. 04.25  114354 GEN     65. 040000 LB0:-00004315
...ERF 02     114654 GEN     61. 040000 LB0:-00020133
...INI 20.01  114254 GEN     60. 040000 LB0:-00004553
...QUE 1.0    115654 GEN     50. 040000 LB0:-00005367
...PRI 1.0    115554 GEN     50. 040000 LB0:-00005367
...ACS 01     115154 GEN     50. 040000 LB0:-00020107
...BOO 03.4   115054 GEN     50. 040000 LB0:-00003532
ERRLOG 02     114554 GEN     50. 040000 LB0:-00020443
...LOA 03.3   113754 GEN     50. 040000 LB0:-00016670
...HEL 01.24  113554 GEN     50. 040000 LB0:-00020010
...BYE 02.2   113454 GEN     50. 004000 LB0:-00017436
...UNL 02.8   112554 GEN     50. 040000 LB0:-00016763
LP0:    LOADED
DL0:    LOADED
DL1:    LOADED
DL2:    LOADED
DL3:    LOADED
DR0:    LOADED
DR1:    LOADED
DR2:    LOADED
DR3:    LOADED
DR4:    LOADED
DR5:    LOADED
DR6:    LOADED
DR7:    LOADED
MT0:    LOADED
MT1:    LOADED
MT2:    LOADED
MT3:    LOADED
CO0:  TT0:
TT0:    LOADED
TT1:    LOADED
TT2:    LOADED
TT3:    LOADED
TT4:    LOADED
TT5:    LOADED
TT6:    LOADED
TT7:    LOADED
TT10:    LOADED
TT11:    LOADED
TT12:    LOADED
TT13:    LOADED
TT14:    LOADED
TT15:    LOADED
TT16:    LOADED
TT17:    LOADED
TT20:    LOADED
TT21:    LOADED
TT22:    LOADED
TT23:    LOADED
TT24:    LOADED
TT25:    LOADED
TT26:    LOADED
TT27:    LOADED
TT30:    LOADED
TT31:    LOADED
TT32:    LOADED
TT33:    LOADED
TT34:    LOADED
TT35:    LOADED
TT36:    LOADED
TT37:    LOADED
TT40:    LOADED
NL0:  
TI0:  
CL0:  TT0:
LB0:  DL0:
SY0:  DL0:
VMR>^Z

>; 
>;     When the indirect file exits, boot in your target system,
>;     set the date and time, and save the system with a bootstrap.
>;     When your system reboots itself, purge the old task files.
>; 
>; E.G.
>;     >BOO RSX11M
>; 
>;     RSX11M V03.2 BL26 
>;     >TIM 9:00:00 13-JAN-56
>;     >SAV /WB
>; 
>;     RSX11M V03.2 BL26   124K  MAPPED
>;     >RED DL0:=SY:
>;     >RED DL0:=LB:
>;     >MOU DL0:RSXM26
>;     >@[1,2]STARTUP
>;     >* Enter date and time ( dd-mmm-yy hh:mm ) [S]:
>;     >TIM 9:00:04 13-JAN-56
>;     >@ <EOF>
>;     >SET /UIC=[1,54]
>;     >RUN $PIP
>;     PIP>*.*/PU
>;     PIP>^Z
>;     >
>;
>;     An alternate version of SYSLIB called ANSLIB has been created
>;     on the RSXM26 disk to take into account ANSI support and Big-buffering.
>;
>;     Since you have selected ANSI magtape support you may want to
>;     rebuild PIP and other utilities in SYSGEN phase III to take
>;     advantage of ANSI support.  Note this will cause an increase 
>;     in the size of the utility compared with the non-ANSI version.
>;
>;     Don't forget to create accounts after saving your system
>ASN =LB:
>;
>; End of SYSGEN phase II at 02:08:33 on 10-JUL-99
>;
>@ <EOF>
>INS $BOO;-1
>BOO [1,54]
XDT: 26

XDT>G
RSX11M V3.2 BL26  


>
SAV /WB

  RSX-11M V3.2 BL26   124K   MAPPED
>RED DL:=SY:
>RED DL:=LB:
>MOU DL:RSXM26
>@DL:[1,2]STARTUP
>* Enter date and time ( dd-mmm-yy hh:mm ) [S]: 2:08 10-JUL-99
>TIM 2:13 10-JUL-99
>@ <EOF>
>MOU DL1:/OVR
>ASN DL1:=SY:
>SET /UIC=[1,24]
>INS $EDI
>EDI ACNTBLD.CMD
[00016 LINES READ IN]
[PAGE    1]
*
TK:[1,54]ACNT/-FP/MM/PR,MP:[1,34]ACNT/-SP=[1,24]ACNTBLD/MP
*
TASK=ACNT
*
PAR=GEN:0:40000
*
EXTTSK=4000
*C/4000/3000/
EXTTSK=3000
*EX
[EXIT]

>ASN LB:=MP:
>ASN LB:=TK:
>INS $TKB
>TKB @ACNTBLD
>INS $PIP
>PIP LB:[*,*]/PU\UP/\*.*/PU
>RUN $ACNT
INS -- WARNING - PRIVILEGED TASK OVERMAPS I/O PAGE
 * ACCOUNT FILE MAINTENANCE PROGRAM *
OPTIONS ARE: A - ADD, C - CREATE FILE, D - DELETE, E - EXAMINE,
L - LIST, M - MODIFY, S - SORT,  CTRL/Z - EXIT
ENTER OPTION: C
ENTER MAXIMUM NUMBER OF ACCOUNTS: 128
OPTIONS ARE: A - ADD, C - CREATE FILE, D - DELETE, E - EXAMINE,
L - LIST, M - MODIFY, S - SORT,  CTRL/Z - EXIT
ENTER OPTION: A
ENTER ACCOUNT OR <ESC> FOR OPTIONS ( N,N ): 1,1
PASSWORD ( <=6 CHARS. ): SYSTEM
DEFAULT SYSTEM DEVICE ( DDU ): LB0
FIRST NAME ( <=12 CHARS. ): SYSTEM
LAST NAME ( <=14 CHARS. ): SYSTEM
UFD LB00:[001,001]
UFD -- DIRECTORY ALREADY EXISTS
>
ENTER ACCOUNT OR <ESC> FOR OPTIONS ( N,N ): 
OPTIONS ARE: A - ADD, C - CREATE FILE, D - DELETE, E - EXAMINE,
L - LIST, M - MODIFY, S - SORT,  CTRL/Z - EXIT
ENTER OPTION: ^Z
OPERATION COMPLETE

>
